Did you notice these signs before the air compressor failed?
The various faults of the compressor often do not appear suddenly, but have certain omen, sometimes appearing in various visions, sometimes appearing as numerical values on the instrument.
Therefore, today we will discuss the various signs before the occurrence of various types of compressor failures, and provide reference for the majority of compressor users to predict equipment failures and maintenance in advance.

1, abnormal noise, abnormal vibration
An abnormal sound that occurs during operation is an "alarm" for equipment failure.
The vibration is severe during operation.
The reasons for the abnormal noise of the compressor may be:
The bearing of the main engine is worn, the shaft is unbalanced, and the yin and yang rotor are damaged.
The main engine is under heavy load, and the pressure on the rolling or pipe network is unbalanced;
Bolts, nuts, washers and fixing brackets are loose;
Inside the equipment, debris and foreign matter fall into the device;
It is also possible because the compressor unit is running close to the overhaul period.
At this time, the axial and radial turbulence of the screw gradually tends to the maximum design allowable value, which causes a large change in the gap between the screw and the screw, between the screw and the main body casing and the front and rear end faces, thereby causing friction. , vibration and various sounds.
Second, running a leak
Leakage of the lubricating oil of the equipment;

Leakage occurs in compressed air, etc., and sometimes the sound of air leakage can be clearly heard;
Leakage of cooling water, etc.
The main reason for the leakage is that the equipment and accessories are not aged or maintained, especially due to the bad behavior of the employees or the inadvertent operation.
These seemingly small problems can lead to very serious consequences, even though they are hidden behind various appearances.
Taking compressed air as an example, leakage not only directly wastes expensive electric energy, but also causes a burden on electricity, and may also cause system pressure drop, which reduces the functional efficiency of the pneumatic equipment and shortens the life of the equipment.
At the same time, air leakage can cause equipment to circulate more frequently, thereby increasing the operating time of the air compressor, which results in additional maintenance requirements and potentially increased unplanned downtime.
Simply put, compressed air leakage increases unnecessary compressor capacity.
Leaks, combined with the common problem of higher than the required system working pressure, lead to so-called “false demands” that keep the compressor loaded and innocent.
All of this has a negative impact on productivity and shortens the life of almost all system equipment and pneumatic tools. Excessive energy use and reduced equipment life, this is a double blow to the factory owners, must be taken seriously.
Third, special smell
When the motor is overheated and the lubricating oil is burned, a special smell is emitted.
When the circuit is short-circuited, the insulation material such as the ground wire is burnt, there is a burnt smell.
Materials such as rubber emit a burnt smell.
According to media reports, on May 25, 2017, a gas leak occurred in the workshop of Kecheng Technology (Suqian) Co., Ltd. in Suqian City. More than 80 employees were hospitalized after inhaling a certain gas.
Later, after investigation by the Sushang Industrial Park Management Committee of Suqian City, the accident was a secondary accident caused by mechanical failure of the compressor caused by the wear of the screw bearing of the air compressor of the A6 workshop of Kecheng Technology.
According to the management committee of the park, the cause of the accident was that the bearing seat and the screw were locked by the power air compressor, and a large amount of thermal energy was generated due to the friction, which caused the cracking of the lubricating oil in the screw cylinder to produce small molecular hydrocarbons, and the decomposition of the additive was generated. Compounds such as sulfur and phosphorus form irritating gases that enter the workbench through the compression piping system and are dissipated in the workshop, causing operator discomfort.
This special smell of the compressor caused many people to be hospitalized. Although the worker has already experienced the smell, it can quickly lock the cause and location of the fault through special smell, and also ring for the user when the compressor smells. Alarm bell.
summary
The appearance of compressor failures is often not an abrupt appearance, but a certain omen, sometimes with various visions, sometimes with numerical values on the instrumentation.
Therefore, we must be vigilant against various signs of failure, and help operators and maintenance personnel to detect the signs of accidents early and prevent them from happening.




